Installing an American flag should be simple, but for most people it turns into a weekend project filled with trips to the hardware store, DIY tutorial videos, and a little hope that everything stays put. However, with an Elizabeth Ross Flag Kit, it’s a 10-minute job.
Every Elizabeth Ross Flag Kit comes pre-assembled with everything you need, including a handcrafted 3’x5’ American flag, a 6’ flagpole, spinning rings, a finial, mounting bracket, and all the necessary hardware. There’s no hunting for compatible parts, no second-guessing whether the flagpole fits the bracket, and no need to even attach the flag. Everything is matched, tested, and ready to install. Just mount the bracket and your new flag is ready to fly.
The only variable? The surface you’re mounting your flag to. Whether your home has brick, vinyl siding, concrete, or wood, the installation process is simple and straightforward. Our guide walks you through each surface type, providing step-by-step instructions, so you can go from unboxing to flying your flag in minutes.
What’s Inside an Elizabeth Ross Flag Kit
Before we get into the installation, here’s a list of everything you’ll be working with. Each Elizabeth Ross American Flag Kit includes:
- A 3'x5' American flag with embroidered stars, made in the USA
- A 6' black aluminum flagpole or hardwood ash pole (depending on the kit you choose)
- A gold, silver, or wooden finial
- Spinning rings that keep the flag from wrapping around the pole
- A black mounting bracket designed for 1" flagpoles
- Mounting screws and wall anchors, all packaged in a branded drawstring pouch
Everything comes pre-assembled, meaning the flag is already attached to the pole with the spinning rings and finial already in place. The only piece you need to install is the mounting bracket.
Tools You’ll Need to Install Your Flag Kit
The Elizabeth Ross Flag Kit keeps things simple, but you will need a few basic tools depending on your home's surface type.
For all surfaces you’ll need:
- A drill
- A level
- A pencil for marking
- A tape measure
Surface-specific additions:
- Brick or concrete: Masonry drill bit (the wall anchors are included in the kit)
- Vinyl or aluminum siding: A stud finder to locate framing behind the siding
- Wood: A standard drill bit for pilot holes
That's it. The screws and anchors are already included in the kit.
How to Install an American Flag on Brick
Brick is one of the most secure surfaces for mounting an American flag. The material is strong, stable, and holds fasteners well when you use the right hardware.
- Choose your location. The most common spots are next to the front door, on a porch column, or beside the garage. Position the bracket high enough that the bottom of the flag won't brush against railings, shrubs, or anyone walking beneath it. For most homes, this puts the bracket somewhere between 5 and 6 feet off the ground.
- Hold the bracket in place and mark your holes. Use a level to make sure the bracket is straight, then mark the screw holes with a pencil.
- Drill pilot holes with a masonry bit. Use a bit that matches the size of the wall anchors included in your kit. Drill to the depth of the anchor. Clear the dust from the holes with a quick blast of air or a brush.
- Insert the included wall anchors and secure the bracket. Tap the anchors into the pilot holes, then drive the included screws through the bracket and into the anchors. Tighten until the bracket is snug and doesn't wobble.
- Slide in the flagpole and you're done. The Elizabeth Ross Flag Kit pole slides right into the bracket and your flag is flying.
- Pro tip: Always drill into the brick itself, not the mortar joints. Brick is significantly stronger and provides a much more secure hold.
How to Install an American Flag on Vinyl or Aluminum Siding
Siding is the most common exterior surface on American homes, and it works just fine for a flag mount. The key is making sure you're anchoring into something solid behind the siding, not just the siding itself.
- Locate the studs behind the siding. Use a stud finder to locate the framing behind your siding. This is critical. Siding alone is too thin and flexible to support a flag bracket and pole in the wind. You need to anchor into the studs or structural sheathing behind it.
- Choose your mounting spot and mark the holes. Mount the bracket high enough so the flag clears railings, light fixtures, and foot traffic below. For most homes, somewhere between 5 and 6 feet off the ground works well. Hold the bracket in place, check it with a level, and mark the screw positions. Try to align at least one screw with a stud.
- Drill pilot holes through the siding. Use a standard drill bit sized for your screws. Drill through the siding and into the stud behind it.
- Secure the bracket with the included screws. Drive the screws through the bracket, through the siding, and into the stud. Tighten firmly but don't over-torque. You don't want to crack or warp the siding.
- Insert the flagpole. Slide the Elizabeth Ross pre-assembled flagpole into the bracket and you’re flying.
- Pro tip: If you can't hit a stud, use a siding mount block or a piece of treated plywood behind the siding as a backer. This distributes the load and prevents the bracket from pulling free in strong wind.
How to Install an American Flag on Concrete or Stucco
Concrete walls, stucco exteriors, and cinder block surfaces are rock-solid mounting points. The process is similar to brick, you just need the right anchors.
- Choose your location and hold the bracket in place. Aim for a spot where the flag will hang freely, with the bracket mounted between 5 and 6 feet off the ground so the flag clears anything below it. Mark your holes with a pencil and check with a level.
- Drill pilot holes with a masonry bit. Concrete and stucco require a hammer drill or a rotary hammer for best results. Use a masonry bit that matches the included wall anchors and drill to the appropriate depth.
- Clean out the holes. Concrete dust can prevent anchors from seating properly. Blow out or brush out each hole before inserting your anchors.
- Insert the included wall anchors and mount the bracket. Tap the anchors into the pilot holes, then drive the included screws through the bracket and tighten until secure.
- Insert your flagpole and fly your flag. Same as every other surface, the pre-assembled flagpole slides into the bracket and you're done.
- Pro tip: For stucco, be aware that the stucco layer itself is thin. Your fasteners need to pass through the stucco and bite into the concrete, block, or framing beneath it. If you're unsure what's behind your stucco, start with a small test hole to check.
How to Install an American Flag on Wood (Posts, Trim, Porch Columns)
Wood is the easiest surface for American flag kit installation. If you have a wooden porch post, column, fascia board, or exterior trim, you can have your flag up in just a few minutes.
- Choose your mounting spot. Porch posts and columns are the most popular choice. Make sure the flag will have enough clearance to fly without catching on railings, walls, or the roof overhang. Mounting the bracket between 5 and 6 feet off the ground keeps the flag above foot traffic and gives it room to fly.
- Hold the bracket in place and mark your holes. Level it. Mark it. Simple.
- Drill pilot holes. Use a standard drill bit slightly smaller than your screw diameter. This prevents the wood from splitting and gives the screws something to grip.
- Drive the included screws. The screws that come with the kit work well for solid wood surfaces. Drive them in until the bracket is tight and secure against the wood.
- Slide in the pole and admire the view. The whole process takes just a few minutes on wood.
- Pro tip: If you're mounting to a painted surface, consider placing a small rubber or felt washer behind the bracket to protect the paint from scratching. Also, check that the wood is solid and not rotted. Soft or deteriorated wood won't hold a bracket securely.
Why a Pre-Assembled Flag Kit Makes Installation Easier
Most of the frustration people experience when installing an American flag has nothing to do with the actual mounting. It's the prep work and figuring out which pole fits which bracket, whether the flag grommets match the attachment hardware, and whether everything you bought is actually compatible.
A pre-assembled American flag kit eliminates all of that worry. With an Elizabeth Ross Flag Kit, the flag is already on the pole, the spinning rings are in place, the bracket is designed to fit the included pole, and even the mounting screws and wall anchors are included in the kit. The only thing you're installing is the bracket itself, which requires just three screws on all surfaces.
That's how a project most people budget a full afternoon for turns into a 10-minute job.
Choosing the Right Elizabeth Ross Flag Kit for Your Home
Elizabeth Ross offers three flag kit options, each built around the same premium 3'x5' American flag with embroidered stars.
Black Aluminum Pole with Gold Finial - A clean, classic look. The black pole creates sharp contrast against most home exteriors, and the gold finial adds a traditional finishing touch.
Black Aluminum Pole with Silver Finial - Same sleek black pole with a silver finial for a more modern, understated accent. This is the best seller for a reason and it looks great on just about everything.
Hardwood Ash Pole with Wooden Finial - A natural hardwood pole for homeowners who prefer a warmer, more traditional aesthetic. The 3" wooden finial completes the classic look.
All three kits include the same premium American-made flag, spinning rings, and mounting bracket. The difference is purely a matter of style, so choose the one that best complements your home's exterior.
Common American Flag Installation Mistakes to Avoid
A few quick things to watch out for:
- Mounting too close to obstructions. Make sure the flag has room to fly freely. If it's catching on gutters, light fixtures, or tree branches, it will wear out faster and won't display properly.
- Skipping the pilot holes. Driving screws directly into brick, concrete, or hardwood without pilot holes can crack the surface or strip the screw. Take the extra 30 seconds.
- Using the wrong fasteners for the surface. The Elizabeth Ross Flag Kit includes both screws and wall anchors, so you're covered for most surfaces. Use the wall anchors for brick and concrete, and the screws alone for wood. For siding, make sure you're driving into a stud behind the siding for a solid hold.
- Mounting into siding without hitting a stud. Siding alone can't support the load, especially in wind. Always anchor into the framing behind it.
- Ignoring the level. A crooked bracket means a crooked flag. It takes five seconds to check with a level.
Quick American Flag Installation Checklist
Before you start, make sure you have everything ready:
- Elizabeth Ross Flag Kit (flag, pole, spinning rings, finial, bracket, screws, and wall anchors all included)
- Drill and appropriate drill bit for your surface
- Level
- Pencil and tape measure
- Stud finder (for siding installations)
Once you've got your tools lined up, the bracket goes up in minutes and the pre-assembled American flag and pole slide right in.
Final Thoughts
Installing an American flag on your home shouldn't require a hardware store scavenger hunt or a full afternoon of trial and error. With the right kit, it's one of the simplest home projects you'll ever take on.
Every Elizabeth Ross Flag Kit is designed to make this easy. You’ll receive a premium 3’x5’ American-made flag, a quality pole, and all the hardware you need, pre-assembled and ready to mount on any surface. Pick your kit, grab a drill, and you'll be flying your flag in no time.
